Mechanical properties, microstructure, and fracture behavior of friction stir welded AA7075 joints with conical pin and conical threaded pin type tools

Document Type : Article

Authors

Department of Mechanical Engineering, Vishwakarma Institute of Information Technology, Pune, Maharashtra State, 411048, India

Abstract

This study investigates the mechanical properties, microstructure, and fracture behavior of friction stir welded (FSWed) AA7075 joints considering the influence of process parameters and tool geometry. FSWed joints are produced with a conical pin and conical threaded pin type tools using tool rotational speeds of 1400 and 2000 rpm and welding speeds of 20 and 40 mm/min. The FSWed joint showed higher values of the tensile strength (188 MPa), percentage elongation (5.7%), and microhardness (137 HV) with the conical threaded pin type tool. However, the conical pin type tool produced a minimum surface roughness of 9.59 μm. A comparatively lower tensile strength observed for the FSWed joint with conical pin type tool could be attributed to their coarser, elongated, and heterogeneous grain distribution and porosity defects in the welding zone. No significant difference has been observed in the microhardness with the conical pin and conical threaded pin type tools. The fracture of the FSWed joint predominantly occurred in the heat-affected zone during the tensile test. The FSWed joint produced with a conical threaded pin showed better mechanical properties, favorable microstructure, and ductile type fracture behavior at a welding speed of 40 mm/min and tool rotation of 2000 rpm.

Keywords


References:
1. Cetkin, E., Celik, Y.H., and Temiz, S. "Microstructure and mechanical properties of AA7075/AA5182 jointed by FSW", J. Mater. Process. Technol, 268, pp. 107- 116 (2019).
2. Sharma, C., Dwivedi, D.K., and Kumar, P. "Effect of welding parameters on microstructure and mechanical properties of friction stir welded joints of AA7039 aluminum alloy", Mater. Des, 36, pp. 379-390 (2012).
3. Szklarska-Smialowska, Z. "Pitting corrosion of aluminum", Corros. Sci., 41, pp. 1743-1767 (1999).
4. Nosko, M., Stepanek, M., Zifcak, P., et al. "Solid-state joining of powder metallurgy Al-Al2O3 nanocomposites via friction-stir welding: Effects of powder particle size on the weldability, microstructure, and mechanical property", Mater. Sci. Eng. A., 754, pp. 190-204 (2019).
5. Zhang, C., Cao, Y., Huang, G., et al. "Influence of tool rotational speed on local microstructure, mechanical and corrosion behavior of dissimilar AA2024/7075 joints fabricated by friction stir welding", J. Manuf. Process, 49, pp. 214-226 (2020).
6. Zhang, J., Upadhyay, P., Hovanski, Y., et al.  Highspeed friction stir welding of AA7075-T6 sheet: Microstructure, mechanical properties, micro-texture, and thermal history", Metall. Mater. Trans. A Phys.  Metall. Mater. Sci, 49, pp. 210-222 (2018).
7. Rao, T.S., Reddy, G.M., and Rao, S.R.K. "Microstructure and mechanical properties of friction stir welded AA7075-T651 aluminum alloy thick plates", Trans. Nonferrous Met. Soc. China (English Ed.), 25, pp. 1770-1778 (2015).
8. Elatharasan, G. and Kumar, V.S.S. "Corrosion analysis of friction stir-welded aa 7075 aluminium alloy", Stroj. Vestnik/Journal Mech. Eng, 60, pp. 29-34 (2014).
9. Rao, T.S., Rao, S.R.K., and Reddy, G.M. "Microstructure and fracturing behavior of AA7075-T651 aluminum alloy cooled during friction stir welding", Met. Sci. Heat Treat, 61, pp. 379-386 (2019).
10. Ipekoglu, G., Kiral, B.G., Erim, S., et al. "Investigation of the effect of temper condition on the friction-stir weldability of AA7075 Al-alloy plates", Mater. Tehnol, 46, pp. 627-632 (2012).
11. Barbini, A., Carstensen, J., and Santos, J.F. dos. "Influence of a non-rotating shoulder on heat generation, microstructure and mechanical properties of dissimilar AA2024/AA7050 FSW joints", J. Mater. Sci. Technol, 34, pp. 119-127 (2018).
12. Chen, S., Li, X., Jiang, X., et al. "The effect of microstructure on the mechanical properties of friction stir welded 5A06 Al Alloy", Mater. Sci. Eng. A, 735, pp. 382-393 (2018).
13. Chen, H., Fu, L., and Liang, P. "Microstructure, texture and mechanical properties of friction stir welded butt joints of 2A97 Al-Li alloy ultra-thin sheets", J. Alloys Compd, 692, pp. 155-169 (2017).
14. Azeez, S.T. and Akinlabi, E.T. "Effect of processing parameters on microhardness and microstructure of a double-sided dissimilar friction stir welded aa6082-t6 and aa7075-t6 aluminum alloy", Mater. Today Proc, 5, pp. 18315-18324 (2018).
15. Chinchanikar, S., Gharde, S., and Gadge, M. "Investigation of tool forces, weld bead micro-hardness and surface roughness during friction stir welding of aluminium 6063 alloy", Adv. Mater. Process. Technol., 8, pp. 1-9 (2020).
16. Kumar, P.V., Reddy, G.M., and Rao, K.S. "Microstructure and pitting corrosion of armor grade AA7075 aluminum alloy friction stir weld nugget zone - Effect of post weld heat treatment and addition of boron carbide", Def. Technol, 11, pp. 166-173 (2015).
17. Kumar, P.S. and Chander M.S. "Effect of tool pin geometry on FSW dissimilar aluminum alloys - (AA5083 & AA6061)", Mater. Today Proc, 39, pp. 472-477 (2020).
18. Mastanaiah, P., Sharma, A., and Reddy, G.M. "Role of hybrid tool pin profile on enhancing welding speed and mechanical properties of AA2219-T6 friction stir welds", J. Mater. Process. Technol, 257, pp. 257-269 (2018).
19. Amirafshar, A. and Pouraliakbar, H. "Effect of tool pin design on the microstructural evolutions and tribological characteristics of friction stir processed structural steel", Meas. J. Int. Meas. Confed, 68, pp. 111-116 (2015).
20. Beygi, R., Mehrizi, M.Z, Verdera, D., et al. "Influence of tool geometry on material flow and mechanical properties of friction stir welded Al-Cu bimetals", J. Mater. Process. Technol, 255, pp. 739-748 (2018).
21. Kumar, K., Kailas, S.V., and Srivatsan, T.S. "Influence of tool geometry in friction stir welding", Mater.b Manuf. Process, 23, pp. 188-194 (2008).
22. Banik, A., Saha, A., Barma, J.D., et al. "Determination of best tool geometry for friction stir welding of AA 6061-T6 using hybrid PCA-TOPSIS optimization method", Meas. J. Int. Meas. Confed, 173, p. 108573 (2021).
23. Krasnowski, K., Hamilton, C., and Dymek, S. "Influence of the tool shape and weld configuration on microstructure and mechanical properties of the Al 6082 alloy FSW joints", Arch. Civ. Mech. Eng, 15, pp. 133-141 (2015).
24. Rao, M.S.S., Kumar, B.V.R.R., and Hussain, M.M. "Experimental study on the effect of welding parameters and tool pin profiles on the IS:65032 aluminum alloy FSW joints", Mater. Today Proc., 4, pp. 1394- 1404 (2017).
25. Badarinarayan, H., Shi, Y., Li, X., et al. "Effect of tool geometry on hook formation and static strength of friction stir spot welded aluminum 5754-O sheets", Int. J. Mach. Tools Manuf, 49, pp. 814-823 (2009).
26. Yuvaraj, K.P., Varthanan, P.A., Haribabu, L., et al. "Optimization of FSW tool parameters for joining dissimilar AA7075-T651 and AA6061 aluminium alloys using Taguchi Technique", Mater. Today Proc, 45(2), pp. 919-925 (2020). https://doi.org/10.1016/j.matpr.2020.02.942.
27. John, J., Shanmughanatan, S.P., and Kiran, M.B. "Effect of tool geometry on microstructure and mechanical properties of friction stir processed AA2024- T351 aluminium alloy", Mater. Today Proc, 5, pp. 2965-2979 (2018).
28. Suri, A. "An improved FSW tool for joining commercial aluminum plates", Procedia Mater. Sci, 6, pp. 1857-1864 (2014).
29. Abolusoro, O.P. and Akinlabi, E.T. "Experimental investigations of tool pin geometry and process parameter influence on mechanical property of friction stir welded 6101-T6 and 7075-T651 aluminium alloys", Journal of Physics: Conference Series, 1378, pp. 1-9 (2019).
30. Abolusoro, O.P., Akinlabi, E.T., and Kailas, S.V. "Tool rotational speed impact on temperature variations, mechanical properties and microstructure of friction stir welding of dissimilar high-strength aluminium alloys", J. Brazilian Soc. Mech. Sci. Eng, 42, p. 176 (2020).
31. Abolusoro, O.P., Akinlabi, E.T., and Kailas, S.V. "Impact of tool profile on mechanical behavior and material flow in friction stir welding of dissimilar aluminum alloys", Materwiss. Werksttech, 51, pp. 725-731 (2020).
32. Pouraliakbar, H., Beygi, R., Fallah, V., et al. "Processing of Al-Cu-Mg alloy by FSSP: Parametric analysis and the effect of cooling environment on microstructure evolution", Mater. Lett, 308, pp. 1-5 (2022). DOI: 10.1016/j.matlet.2021.131157.
33. Goyal, A. and Garg, R.K. "Modeling and optimization of friction stir welding parameters in joining 5086 H32 aluminium alloy", Sci. Iran, 26, pp. 2407-2417 (2019).
34. Kumar, P.S. and Chander, M.S. "Effect of tool pin geometry on FSW dissimilar aluminum alloys - (AA5083 & AA6061)", Mater. Today Proc, 39, pp. 472-477 (2020).
35. Jabraeili, R., Jafarian, H.R., Khajeh, R., et al. "Effect of FSW process parameters on microstructure and mechanical properties of the dissimilar AA2024 Al alloy and 304 stainless steel joints", Mater. Sci. Eng. A., 814, pp. 1-13 (2021).
36. Liu, P., Sun, S., and Hu, J. "Effect of laser shock peening on the microstructure and corrosion resistance in the surface of weld nugget zone and heat-affected zone of FSW joints of 7050 Al alloy", Opt. Laser Technol, 112, pp. 1-7 (2019).
37. Khajeh, R., Jafarian, H.R., Seyedein, S.H., et al. "Microstructure, mechanical and electrical properties of dissimilar friction stir welded 2024 aluminum alloy and copper joints", J. Mater. Res. Technol, 14, pp. 1945-1957 (2021).
38. Wang, W., Yuan, S., Qiao, K., et al. "Microstructure and nanomechanical behavior of friction stir welded joint of 7055 aluminum alloy", J. Manuf. Process, 61, pp. 311-321 (2021).
39. Xu, Y., Ke, L., Mao, Y., et al. "Interfacial microstructure evolution of thick plate Al/Mg FSW: Effect of pin size", Mater. Charact, 174, pp. 1-7 (2021).
40. Beygi, R., Mehrizi, M.Z., Verdera, D., et al. "Influence of tool geometry on material flow and mechanical properties of friction stir welded Al-Cu bimetals", J. Mater. Process. Technol, 255, pp. 739-748 (2018).
41. Chinchanikar, S. and Gaikwad, V.S. "State of the art in friction stir welding and ultrasonic vibrationassisted friction stir welding of similar/dissimilar aluminum alloys", J. Comput. Appl. Res. Mech. Eng, 11(1), pp. 67-100 (2021).
42. Gaikwad, V.S. and Chinchanikar, S. "Investigation on surface roughness, ultimate tensile strength, and microhardness of friction stir welded AA7075-T651 joint", Mater. Today Proc, 46(17), pp. 8061-8065 (2021).
43. Gaikwad, V.S. and Chinchanikar, S. "Mechanical behaviour of friction stir welded AA7075-T651 joints considering the effect of tool geometry and process parameters", Advan. in Mate. & Proce. Techno. 10.1080/2374068X.2021.1976554.
44. Beygi, R., Kazeminezhad, M., Mehrizi, M.Z., et al. "Friction stir butt welding of Al-Cu bilayer laminated composites: analysis of force, torque, and temperature", Int. J. Adv. Manuf. Technol, 88, pp. 393-400 (2017).
45. Beygi, R., Kazeminezhad, M., and Kokabi A.H. "Microstructural evolution and fracture behavior of friction-stir-welded Al-Cu laminated composites", Meta. and Mate.s Trans. A., 45A., pp. 361-370 (2014).