Optimal winding selection for wound-rotor resolvers

Document Type : Article

Authors

1 Department of Electrical Engineering, Sharif University of Technology, Tehran, Iran

2 Department of Electrical Engineering, Iran University of Science and Technology, Tehran, Iran

Abstract

Wound-rotor (WR) resolvers are the most commercially used resolvers in industrial applications. In this paper, the effect of different winding arrangements on the accuracy of WR resolvers is discussed. Three windings are proposed for the stator of the resolver that are involved on-tooth overlapping winding, distributed lap winding and distributed concentric winding. Those windings are also applied to the rotor. All the rotor windings are assumed to be single phase and two-phase. Therefore, the effect of damper winding is also studied in the paper. The analysis is done using time stepping finite element method and the most accurate resolver is built and tested. Close agreement between the experimental measurements and the finite element results confirms the obtained results.

Keywords

Main Subjects

References

References:
1. Abolqasemi-Kharanaq, F., Alipour-Sarabi, R., Nasiri-Gheidari, Z., et al. "Magnetic equivalent circuit model for wound rotor  resolver without rotary transformer's core", IEEE Sensors J., 18(21), pp. 8693-8700 (2018).
2. Alipour-Sarabi, R., Nasiri-Gheidari, Z., Tootoonchian,F., et al. "Improved winding proposal for wound rotor resolver using genetic algorithm and winding function approach", IEEE Trans. Industrial Electronics, 66(2), pp. 1325-1334 (2019).
3. Saneie, H., Nasiri-Gheidari, Z., and Tootoonchian, F. "Design-oriented modelling of axial-flux variablereluctance resolver based on magnetic equivalent circuits and Schwarz-Christoffel mapping", IEEE Trans. Industrial Electronics, 65(5), pp. 422-4330 (2018).
4. Ge, X., Zhu, Z.Q., Ren, R., et al. "A novel variable reluctance resolver for HEV/EV applications", IEEE Trans. Ind. Appl., 52(4), pp. 2872-2880 (2016).
5. Ge, X., Zhu, Z.Q., Ren, R., et al. "A novel variable reluctance resolver with nonoverlapping tooth-coil windings", IEEE Trans. Energy Conversion, 30(2), pp. 784-794 (2015).
6. Daniar, A., Nasiri-Gheidari, Z., and Tootoonchian, F. "Performance analysis of linear variable reluctance resolvers based on improved winding function approach", IEEE Trans. Energy Convers., 33(3), pp. 1422-1430 (2018).
7. Daniar, A. and Nasiri-Gheidari, Z. "The influence of different configurations on position error of linear variable reluctance resolvers", 25th Iranian Conference on Electrical Engineering (ICEE), Tehran, Iran, pp. 955-960 (2017).
8. Tootoonchian, F. and Nasiri-Gheidari, Z. "Twelveslot two-saliency variable reluctance resolver with nonoverlapping signal windings and axial flux excitation", IET Electric Power Applications, 11(1), pp. 49-62 (2017).
9. Nasiri-Gheidari, Z. and Tootoonchian, F. "An optimized axial  flux variable reluctance resolver with concentric windings", 24th Iranian Conference on Electrical Engineering (ICEE), Shiraz, Iran, pp. 1284- 1290 (2016).
10. Shang, H., Wang, M., Chen, N., et al. "The effects of stator and rotor eccentricities on measurement accuracy of axial flux variable-reluctance resolver with sinusoidal rotor", 17th International Conference on Electrical Machines and Systems (ICEMS), Hangzhou, China, pp. 1206-1209 (2014).
11. Nasiri-Gheidari, Z., Alipour-Sarabi, R., Tootoonchian, F., et al. "Performance evaluation of disk type variable reluctance resolvers", IEEE Sensors J., 17(13), pp. 4037-4045 (2017).
12. Nasiri-Gheidari, Z., Tootoonchian, F., and Zare, F."Design oriented technique for mitigating position error due to shaft run-out in sinusoidal-rotor variable reluctance resolvers", IET Electric Power Applications,11(1), pp. 132-141 (2017).
13. Bahari, M. and Nasiri-Gheidari, Z. "Longitudinal end effect in variable area linear resolver and its compensating methods", 26th Iranian Conference on Electrical Engineering (ICEE), Mashhad, Iran, pp. 1316-1321 (2018).
14. Zare, F., Nasiri-Gheidari, Z., and Tootoonchian, F. "The effect of winding arrangements on measurement accuracy of sinusoidal rotor resolver under fault condition", Measurement, 131, pp. 162-172 (2019).
15. Tootoonchian, F. "Proposal of a new affordable 2- pole resolver and comparing its performance with conventional wound-rotor and VR resolvers", IEEE Sensors J., 18(13), pp. 5284-5290 (2018).
16. Daniar, A., Nasiri-Gheidari, Z., and Tootoonchian, F. "Position error calculation of linear resolver under mechanical fault conditions", in IET Science, Measurement & Technology, 11(7), pp. 948-954 (2017).
17. Alipour-Sarabi, R., Nasiri-Gheidari, Z., Tootoonchian, F., et al. "Effects of physical parameters on the accuracy of axial flux resolvers", IEEE Trans. Magn., 53(4), pp. 1-11 (2017).
18. Alipour-Sarabi, R., Nasiri-Gheidari, Z., Tootoonchian, F., et al. "Performance analysis of concentrated wound-rotor resolver for its applications in high pole number permanent magnet motors", IEEE Sensors J., 17(23), pp. 7877-7885 (2017).
19. Alipour-Sarabi, R., Nasiri-Gheidari, Z., Tootoonchian, F., et al. "Analysis of winding configurations and slotpole combinations in fractional-slots resolvers", IEEE Sensors Journal, 17(14), pp. 4420-4428( 2017).
20. Nasiri-Geidari, Z. and Tootoonchian, F. "Axial flux resolver design techniques for minimizing position error due to static eccentricities", IEEE Sensors Journal, 15(7), pp. 4027-4034 (2015).
21. Figueiredo, J. "Resolver models for manufacturing", IEEE Trans. Industrial Electronics, 58(8), pp. 3693- 3700 (2011).
22. Tootoonchian, F. "Effect of damper winding on accuracy of wound-rotor resolver under static-, dynamic and mixed-eccentricities", IET Electric Power Applications, 12(6), pp. 845-851 (2018).
23. Tootoonchian, F., Abbaszadeh, K., and Ardebili, M. "Novel axial flux brushless resolver analysis and optimization using 3D finite element and DQ model methods", Iranian Journal of Electrical and Electronic Engineering, 8(3), pp. 243-258 (2012).
24. Nasiri-Gheidari, Z. "Design, performance analysis, and
prototyping of linear resolvers", IEEE Trans. Energy Convers., 32(4), pp. 1376-1385 (2017).
25. Saneie, H., Nasiri-Gheidari, Z., and Tootoonchian, F. "Analytical model for performance prediction of linear
resolver", IET Electric Power Applications, 11(8), pp. 1457-1465 (2017).
26. Saneie, H., Alipour-Sarabi, R., Nasiri-Gheidari, Z., and Tootoonchian, F. "Challenges of finite element analysis of resolvers", In IEEE Transactions on Energy Conversion, 34(2), pp. 973-983 (2019). DOI: 10.1109/TEC.2018.2881465.
Scientia Iranica
Volume 28, Issue 6 - Serial Number 6
Transactions on Computer Science & Engineering and Electrical Engineering (D)
November and December 2021
Pages 3429-3436

Files

History

  • Receive Date: 24 December 2018
  • Revise Date: 20 May 2019
  • Accept Date: 21 July 2019

Share

How to cite

Statistics