Multi-flute drill-broach for precision machining of holes

Document Type : Article

Authors

1 Department of Mechanical Engineering and Standardization, S. Toraighyrov Pavlodar State University, Lomov Street 64, Pavlodar, Kazakhstan.

2 Department of Metallurgy, S. Toraighyrov Pavlodar State University, Lomov Street 64, Pavlodar, Kazakhstan.

3 Department of Transport Engineering and Logistics, S. Toraighyrov Pavlodar State University, Lomov Street 64, Pavlodar, Kazakhstan

Abstract

This paper deals with hole-enlarging multiflute drill processing. The analysis of existing structures, their advantages and disadvantages is carried out. Cutting conditions during hole-enlarging multiflute drill processing are shown. A new design of hole-enlarging multiflute drill as a hole-enlarging multiflute drill-broaching tool from broaching-speed steel with carbide plates, as well as a new way of handling the new tools is offered. Hole-enlarging multiflute drill-broaching combines the features of hole-enlarging multiflute drill (in cross section) and the features of broaching tool (in longitudinal section). In this way, it was possible to increase the quality of hole making (size variance, surface roughness), to facilitate the cutting conditions and to increase the durability. The results of prototypes testing are presented.

Keywords

Main Subjects


References:
1. Webzell, S. "Analysis of factors affecting the tool life", Metalwork. Prod., 150, pp. 65-66 (2006).
2. Wang, Y.J., Zhang, D.H., Wu, F.J., Yao, K., and Hou, Z.M. "Simulation of cutting force based on software deform ICICTA: 2009", In Second Int. Conf. Intell. Comput. Technol. Autom., pp. 224-227 (2009).
3. Vogtel, P., Klocke, F., Lung, D., and Terzi, S. "Automatic broaching tool design by technological and geometrical optimization", Procedia CIRP, 33, pp. 496-501 (2015).
4. Vogtel, P., Klocke, F., Puls, H., Buchkremer, S., and Lung, D. "Modelling of process forces in broaching inconel 718", Procedia CIRP, 8, pp. 409-414 (2013).
5. Goncalves, D.A. and Schroeter, R.B. "Modeling and simulation of the geometry and forces associated with the helical broaching process", Int. J. Adv. Manuf. Technol., 83, pp. 205-215 (2016).
6. Hosseini, A. and Kishawy, H.A. "Prediction of cutting forces in broaching operation", J. Adv. Manuf. Syst., 12(01), pp. 1-14 (2013).
7. Kishawy, H.A., Hosseini, A., Moetakef-Imani, B., and Astakhov, V.P. "An energy based analysis of broaching operation: Cutting forces and resultant surface integrity", CIRP Ann. - Manuf. Technol., 61, pp. 107- 110 (2012).
8. Klocke, F., Gierlings, S., Brockmann, M., and Veselovac, D. "Force-based temperature modeling for surface integrity prediction in broaching nickel-based alloys", Procedia CIRP, 13, pp. 314-319 (2014).
9. Lazarev, D.E. and Nasad, T.G. "Cutting tools for improving the quality and productivity of precise holes machining", Mach. Tools., 1, pp. 14-17 (2014).
10. Dudak, N.S., Itybaeva, G.T., Kassenov, A.Z., and Mussina, Z.K. "Part of the 14th Nechnike Sciences", In Proc. IV Int. Sci. - Pract. Conf. "Scientific Ind. Eur. Cont. - 2008", Publishing House <>, Prague, pp. 67-71 (2008).
11. Beju, L.D., Brindasu, D.P., Mutiu, N.C., and Rothmund, J. "Modeling, simulation and manufacturing of drill  flutes", Int. J. Adv. Manuf. Technol., 83(9-12), pp. 2111-2127 (2016).
12. Gupta, K.K., Jain, T., and Deshmukh, M. "Optimization of process parameters in high rpm micro drilling machine", Int. J. Innov. Eng. Technol., 2, pp. 128-130 (2013).
13. Zhao, C., Liang, Z., Zhou, H., and Qin, H. "Investigation on shaping machining method for deep hole keyway based on on-line symmetry detection and compensation", Journal of Mechanical Science and Technology, 31(3), pp. 1373-1381 (2017).
14. Kwon, K.B., Song, C.H., Park, J.Y., Oh, J.Y., Lee, J.W., and Cho, J.W. "Evaluation of drilling efficiency by percussion testing of a drill bit with new button arrangement", International Journal of Precision Engineering and Manufacturing, 15(6), pp. 1063-1068 (2014).
15. Bulat, P. and Volkov, K. "Detonation jet engine. Part 1 - Thermodynamic cycle", Int. J. Environ. Sci. Educ., 11, pp. 5009-5019 (2016).
16. Bulat, P., Volkov, K., and Ilyina, T. "Interaction of a shock wave with a cloud of particles", IEJMEMathematics Educ., 11, pp. 2949-2962 (2016).
17. Baroiu, N., Berbinschi, S., Teodor, V., and Oancea, N. "The modeling of the active surfaces of a multiflute helical drill with curved cutting edge using the SV& Toolbox environment", in: Proc. 13th Int. Conf. Tools-ICT, Miskolc, pp. 259-264 (2012).
18. Baroiu, N., Boazu, D., Vasilache, C.A., and Teodor, V. "Modeling of stress in drills with curved cutting edges", Appl. Mech. Mater., 371, pp. 509-513 (2013).
19. Lorincz, J. "Using digital tools to optimize your cutting tools", Manuf. Eng. Mag., 152(1), pp. 55-62 (2014).
20. Dudak, N.S., Kasenov, A.Z., Musina, Z.K., Itybaeva, G.T., and Taskarina, A.Z. "Hole-making with the use of reaming and broaching tool", Life Sci. J., 11, pp. 282-288 (2014).
21. Byrne, G. "Current state of various materials cutting technology and its practical application area", Ann. CIRP., 52(2), pp. 483-507 (2003).
22. Benes, J. "Overview of cutting tools", Am. Mach., 6, pp. 18-20 (2007).
23. Fisher, R. "The Arrangement of field experiments", J. Minist. Agric. Gt. Britain., 33, pp. 503-513 (1926).
24. Cochran, W.G. "The distribution of the largest of a set of estimated variances as a fraction of their total", Ann. Hum. Genet., 11, pp. 47-52 (1941).